4.5-5KW-YBQY Series-China · Huabang Power Technology Co., Ltd.

Product Information

Safety precautions
Do not grip the front cover or terminal cover when handling the frequency converter. If only the front cover is grasped, it will cause the main body to fall off, posing a risk of injury;
When operating the frequency converter, please follow the steps specified for electrostatic discharge (ESD) prevention measures. Otherwise, the internal circuit of the frequency converter may be damaged due to static electricity.

1. Nameplate and model

Figure 1-1 Product Naming and Nameplate Identification

Three phase 380V~480V, 37G and below have built-in braking units.

2. Inverter model and technical data

Inverter model	Power capacity KVA	Input current A	Output current A	Adapted motor
Inverter model	Power capacity KVA	Input current A	Output current A	KW	HP
Single phase power supply: 220V (-10%~+15), 50/60Hz
VXXX-R40G1	one	five point four	two point three	zero point four	zero point five
VXXX-R70G1	one point five	eight point two	four	zero point seven five	one
VXXX-1R5G1	three	fourteen	seven	one point five	two
VXXX-2R2G1	four	twenty-three	nine point six	two point two	three
Three phase power supply: 220V (-10%~+15), 50/60Hz
VXXX-R40G2	one point five	three point four	two point one	zero point four	zero point five
VXXX-R75G2	three	five	three point eight	zero point seven five	one
VXXX-1R5G2	four	five point eight	five point one	one point five	two
VXXX-2R2G2	five point nine	ten point five	nine	two point two	three
VXXX-4R0G2	eight point nine	fourteen point six	thirteen	three point seven	five
VXXX-5R5G2	seventeen	twenty-six	twenty-five	five point five	seven point five
VXXX-7R5G2	twenty-one	thirty-five	thirty-two	seven point five	ten
VXXX-011G2	thirty	forty-six point five	forty-five	eleven	fifteen
VXXX-015G2	forty	sixty-two	sixty	fifteen	twenty
VXXX-018G2	fifty-seven	seventy-six	seventy-five	eighteen point five	twenty-five
VXXX-022G2	sixty-nine	ninety-two	ninety-one	twenty-two	thirty
VXXX-030G2	eighty-five	one hundred and thirteen	one hundred and twelve	thirty	forty
VXXX-2T37G	one hundred and fourteen	one hundred and fifty-seven	one hundred and fifty	thirty-seven	fifty
Three phase power supply: 380V (-10%~+15), 50/60Hz
VXXX-1R5G4	three	five	three point eight	one point five	two
VXXX-2R2G4	four	five point eight	five point one	two point two	three
VXXX-3R0G4	five	eight	seven point two	three	four
VXXX-4R0G4	five point nine	ten point five	nine	four	five
VXXX-5R5G4	eight point nine	fourteen point six	thirteen	five point five	seven point five
VXXX-7R5G4	eleven	twenty point five	seventeen	seven point five	ten
VXXX-011G4	seventeen	twenty-six	twenty-five	eleven	fifteen
VXXX-015G4	twenty-one	thirty-five	thirty-two	fifteen	twenty
VXXX-018G4	twenty-four	thirty-eight point five	thirty-seven	eighteen point five	twenty-five
VXXX-022G4	thirty	forty-six point five	forty-five	twenty-two	thirty
VXXX-030G4	fifty-four	fifty-seven	sixty	thirty	forty
VXXX-037G4	sixty-three	sixty-nine	seventy-five	thirty-seven	fifty
VXXX-045G4	eighty-one	eighty-nine	ninety-one	forty-five	sixty
VXXX-055G4	ninety-seven	one hundred and six	one hundred and twelve	fifty-five	seventy-five
VXXX-075G4	one hundred and twenty-seven	one hundred and thirty-nine	one hundred and fifty	seventy-five	one hundred
VXXX-090G4	one hundred and fifty	one hundred and sixty-four	one hundred and seventy-six	ninety	one hundred and twenty
VXXX-110G4	one hundred and seventy-nine	one hundred and ninety-six	two hundred and ten	one hundred and ten	one hundred and fifty
VXXX-132G4	two hundred and twenty	two hundred and forty	two hundred and fifty-three	one hundred and thirty-two	one hundred and eighty
VXXX-160G4	two hundred and sixty-three	two hundred and eighty-seven	three hundred and four	one hundred and sixty	two hundred and ten
VXXX-185G4	three hundred and five	three hundred and twenty-three	three hundred and forty	one hundred and eighty-five	two hundred and forty
VXXX-200G4	three hundred and thirty-four	three hundred and sixty-five	three hundred and seventy-seven	two hundred	two hundred and sixty
VXXX-220G4	three hundred and seventy-five	four hundred and ten	four hundred and twenty-six	two hundred and twenty	two hundred and eighty-five
VXXX-250G4	four hundred and four	four hundred and forty-one	four hundred and sixty-five	two hundred and fifty	three hundred and twenty
VXXX-280G4	four hundred and fifty-three	four hundred and ninety-five	five hundred and twenty	two hundred and eighty	three hundred and seventy
VXXX-315G4	five hundred and seventeen	five hundred and sixty-five	five hundred and eighty-five	three hundred and fifteen	four hundred and twenty
VXXX-355G4	five hundred and sixty-five	six hundred and seventeen	six hundred and fifty	three hundred and fifty-five	four hundred and eighty
VXXX-400G4	six hundred and twenty-nine	six hundred and eighty-seven	seven hundred and twenty-five	four hundred	five hundred and thirty
VXXX-450G4	seven hundred and sixteen	seven hundred and eighty-two	eight hundred and twenty	four hundred and fifty	six hundred
VXXX-500G4	eight hundred	eight hundred and twenty	nine hundred	five hundred	six hundred and eighty
VXXX-560G4	nine hundred and thirty	nine hundred and fifty	one thousand and twenty	five hundred and sixty	seven hundred and fifty
VXXX-630G4	one thousand and fifty	one thousand and fifty	one thousand one hundred and twenty	six hundred and thirty	eight hundred and fifty
VXXX-720G4	one thousand and two hundred	one thousand and two hundred	one thousand and three hundred	seven hundred and twenty	nine hundred and sixty

3. Appearance and installation dimensions

Inverter model	Installation hole position mm		Dimensions mm			Installation aperture mm	Weight kg
	A	B	H	W	D
VXXX-R75G4B	seventy-nine	one hundred and fifty-five	one hundred and sixty	eighty-nine	one hundred and thirty-five	Ø4
VXXX-1R5G4B
VXXX-2R2G4B
VXXX-3R0G4B
VXXX-4R0G4B	eighty-six	one hundred and seventy-four	one hundred and eighty-four	ninety-seven	one hundred and forty-five	Ø4
VXXX-5R5G4B
VXXX-7R5G4B	one hundred and thirty-one	two hundred and forty-four	two hundred and fifty-seven	one hundred and forty-seven	one hundred and ninety-five	Ø6
VXXX-011G4B
VXXX-015G4B	one hundred and forty-six	two hundred and ninety-eight	three hundred and twenty	one hundred and seventy	two hundred and sixteen	Ø6
VXXX-018G4B
VXXX-022G4B
VXXX-030G4	one hundred and twenty	three hundred and eighty-four	four hundred	two hundred	two hundred and thirty	Ø7
VXXX-037G4
VXXX-045G4	two hundred	four hundred and ninety-three	five hundred and ten	two hundred and sixty	two hundred and sixty-two	Ø7
VXXX-055G4
VXXX-075G4	two hundred	five hundred and eighty-three	six hundred	three hundred	two hundred and eighty-five	Ø9
VXXX-090G4
VXXX-110G4
VXXX-132G4	two hundred and fifty	seven hundred and fifty-five	seven hundred and eighty	four hundred	three hundred and forty	Ø12
VXXX-160G4
VXXX-185G4
VXXX-200G4	three hundred and fifty	eight hundred and seventy-two	nine hundred	four hundred and fifty	three hundred and sixty-two	Ø12
VXXX-220G4
VXXX-250G4	three hundred and sixty	nine hundred and twenty-two	nine hundred and fifty	five hundred	three hundred and sixty-two	Ø12
VXXX-280G4
VXXX-315G4	four hundred and fifty	one thousand and fifteen	one thousand and fifty	six hundred and fifty	three hundred and seventy-two	Ø13
VXXX-355G4
VXXX-400G4	five hundred	one thousand three hundred and fifteen	one thousand three hundred and fifty	seven hundred	three hundred and eighty	Ø14
VXXX-450G4
VXXX-500G4
VXXX-560G4	six hundred	one thousand four hundred and sixty	one thousand and five hundred	nine hundred	four hundred	Ø14
VXXX-630G4
VXXX-720G4

4. Wiring of main circuit and control circuit

Figure 1-3 Three phase 380V~480V standard wiring diagram

Panel operation

1. Panel operation instructions

The VXXX series frequency converter can perform parameter operation, status monitoring, and control through the LED operation panel.

2. Introduction to LED operation panel

Using the operation panel, the frequency converter can be operated for parameter setting/modification, working status monitoring, and operation control (start, stop).

The appearance and operation key names of the operation panel are shown in the following figure:

Figure 3-1 Schematic diagram of the operation panel

2.1 Function indicator lights

In the table belowThe indicator light is on;Indicates that the light is off.Indicates flashing

Indicator light status		Status description
RUN running indicator light	RUN	Lamp off: Shutdown
RUN running indicator light	RUN	Light on: Running
LOCAL/REMOT Running instruction indicator light	LOCAL/ REMOT	Lamp off: panel control
	LOCAL/ REMOT	Lamp on: Terminal control
	LOCAL/ REMOT	Flashing: Communication Control
REV forward and reverse indicator light	REV	Lamp off: running in forward direction
REV forward and reverse indicator light	REV	Light on: Reverse operation
ALM Tuning/torque control/fault indicator light	ALM	Lamp off: normal operation
	ALM	Lamp on: Torque control mode
	ALM	Slow flashing: tuning state (once per second)
	ALM	Flash: Fault state (4 times/second)

2.2. Keyboard button function

press	Button name	Button Function
PROG	Programming keys	Enter or exit from the first level menu.
ENETER	confirm button	Step by step enter the menu screen and confirm the set parameters.
	Incremental key	The increment of data or parameters.
	Decreasing key	The decreasing of data or parameters.
SHIFT	Shift key	Under the shutdown display interface and operation display interface, display parameters can be cyclically selected; When modifying parameters, you can choose the modification bit of the parameter.
RUN	Run key	Under the start stop control mode of the "operation panel", it is used for running operations.
STOP	Stop/Reset	When in operation, pressing this key can stop the running operation, which is constrained by parameter P7-02; When in a fault alarm state, it can be used for reset operation.
MF.K	Multi functional selection key	Switch between the selected functions based on the set value of P7-01.

2.3 Parameter viewing and modification methods

The operation panel of VXXX frequency converter adopts a three-level menu structure for parameter setting and other operations. The three-level menus are:

1) Functional parameter group (first level menu)
2) Parameters (secondary menu)
3) Parameter setting values (three-level menu)

After entering each level of the menu, when the display flashes, you can press the ▲ key, ▼ keyUse the key to make modifications. The operation process is shown in the following figure:

The three-level menu operation flowchart will display the parameters

a) When operating the third level menu, you can press the PRG key or ENETER key to return to the second level menu. The difference between the two is:

Press the ENTER key to save the set parameters and return to the secondary menu, automatically transitioning to the next parameter; Pressing the PRG key means discarding the current parameter modification and directly returning to the secondary menu of the current parameter number.

b) In the third level menu state, if the parameter does not have a flashing bit, it means that the parameter cannot be modified. Possible reasons include:

(1) This parameter is non modifiable, such as frequency converter type, actual detection parameters, operation record parameters, etc.

(2) This parameter cannot be modified during operation and can only be modified after shutdown.

2.4 Parameter Composition

parameter group	Functional Description	Instructions
P0 ~ PP A0~ AC	Basic Parameters	Operating instructions, frequency instructions, motor parameters, control mode, AI/AO characteristic calibration, optimization control and other parameters.
U0	Monitoring parameter group	Display of basic monitoring parameters for frequency converters.

3. Panel tray opening size

Panel tray hole size diagram

Functional parameter table

The user password for the frequency converter is only used to lock the panel operation. After setting the password, when reading and writing parameters through the keyboard, password verification is required every time the user exits the operation and needs to re-enter; During communication operations, read and write operations can be performed directly without using a password (except for PP and PF groups). The parameter menu in user customized parameter mode is not password protected.

Group P and Group A are basic functional parameters, while Group U is a monitoring functional parameter. The symbol explanations in the parameter table are as follows:

“☆”The set value of this parameter can be changed when the frequency converter is in both shutdown and operation states;
“★”The set value of this parameter cannot be changed when the frequency converter is in operation;
“●”The value of this parameter is the actual detection record value and cannot be changed;
* ": This parameter is a" manufacturer parameter "and is only set by the manufacturer. Users are prohibited from operating it;

1. Basic functional parameter summary table

parameter	name	set the scope	factory default	change
P0 basic functional group
P0-00	GP type	1: G-type (constant torque load model) 2: P-type (fan, pump type load models)	Model determination	●
P0-01	The first motor Control method	0: Speed sensorless vector control (SVC) 1: Vector Control with Speed Sensor (FVC) 2: V/F control	two	★
P0-02	Operation instruction selection	0: Operation panel 1: Terminal 2: Communication	0	☆
P0-03	Main frequency instruction Input selection	0: Number setting (no memory in case of power failure) 1: Numerical setting (power-off memory) 2：AI1 3：AI2 4: Panel potentiometer 5: Pulse setting (DI5) 6: Multi segment instruction 7: Simple PLC 8：PID 9: Communication given	four	★
P0-04	Auxiliary frequency Command input selection	Same as P0-03 (main frequency command input selection)	0	★
P0-05	Auxiliary frequency during superposition Instruction range selection	0: Relative to maximum frequency 1: Relative to the main frequency command	0	☆
P0-06	Auxiliary frequency during superposition Instruction Range	0%~150%	100%	☆
P0-07	Frequency instruction superposition selection	Position: Frequency command selection 0: Main frequency command 1: Main and auxiliary operation results (operation relationship determined by ten digits) 2: Switching between main frequency command and auxiliary frequency command 3: Switching between main frequency instruction and main/auxiliary operation results 4: Switching between auxiliary frequency instruction and main/auxiliary operation results in ten digits: frequency instruction main/auxiliary operation relationship 0: Primary+Secondary 1: Main auxiliary 2: The maximum value of both 3: The minimum value of the two	00	☆
P0-08	preset frequency	0.00Hz~maximum frequency (P0-10)	50.00Hz	☆
P0-09	running direction	0: Default direction of operation 1: Run in the opposite direction to the default direction	0	☆
P0-10	maximum frequency	50.00Hz~500.00Hz	50.00Hz	★
P0-11	Upper limit frequency instruction selection	0: P0-12 setting 1：AI1 2：AI2 3：AI3 4: Pulse setting 5: Communication given	0	★
P0-12	upper frequency limit	Lower limit frequency P0-14~maximum frequency P0-10	50.00Hz	☆
P0-13	Upper frequency offset	0.00Hz~Maximum frequency P0-10	0.00Hz	☆
P0-14	lower cutoff frequency	0.00Hz~upper limit frequency P0-12	0.00Hz	☆
P0-15	carrier frequency	Model determination	Model determination	☆
P0-16	carrier frequency Adjust with temperature	0: No 1: Yes, it is	one	☆
P0-17	Acceleration time 1	0.00s~650.00s(P0-19=2) 0.0s~6500.0s(P0-19=1) 0s~65000s(P0-19=0)	Model determination	☆
P0-18	Deceleration time 1	0.00s~650.00s(P0-19=2) 0.0s~6500.0s(P0-19=1) 0s~65000s(P0-19=0)	Model determination	☆
P0-19	Acceleration and deceleration time unit	0: 1 second 1: 0.1 seconds 2: 0.01 seconds	one	★
P0-21	Auxiliary frequency during superposition Instruction bias frequency	0.00Hz~Maximum frequency P0-10	0.00Hz	☆
P0-22	Frequency command resolution	1：0.1Hz 2:0.01Hz	two	★
P0-23	Digital frequency setting Shutdown memory selection	0: No memory 1: Memory	0	☆
P0-24	Selection of motor parameter group	0: Motor parameter group 1 1: Motor parameter group 2	0	★
P0-25	Acceleration Reference frequency	0: Maximum frequency (P0-10) 1: Set frequency 2：100Hz	0	★
P0-26	Run time frequency instruction P/DOWN benchmark	0: Operating frequency 1: Set frequency	0	★
P0-27	Running instruction bundling Main frequency instruction selection	Position: Operation panel binding frequency source selection 0: No binding 1: Digital frequency setting 2：AI1 3：AI2 4：AI3 5: Pulse setting (DI5) 6: Multi speed 7: Simple PLC 8：PID 9: Communication given Ten digit: Terminal binding frequency source selection Hundred digit: Communication binding frequency source selection	0000	☆
P0-28	Communication protocol selection	0: Modbus protocol 1: Profibus DP, CANopen, Profinet, EtherCAT protocols	0	★
P1 group first motor parameter group
P1-00	Motor type selection	0: Ordinary asynchronous motor 2: Variable frequency synchronous motor (contact manufacturer)	0	★
P1-01	Rated power of motor	0.1kW~1000.0kW	Model determination	★
P1-02	Rated voltage of motor	1V~2000V	Model determination	★
P1-03	Rated current of motor	0.01A~655.35A (inverter power ≤ 55kW) 0.1A~6553.5A (inverter power ≤ 55kW)	Model determination	★
P1-04	Rated frequency of motor	0.01Hz~maximum frequency	Model determination	★
P1-05	Rated speed of motor	1rpm~65535rpm	Model determination	★
P1-06	Stator resistance of asynchronous motor	0.001 Ω~65.535 Ω (frequency converter power ≤ 55kW) 0.0001 Ω~6.5535 Ω (frequency converter power>55kW)	Tuning parameters	★
P1-07	Asynchronous motor rotor resistance	0.001 Ω~65.535 Ω (frequency converter power ≤ 55kW) 0.0001 Ω~6.5535 Ω (frequency converter power>55kW)	Tuning parameters	★
P1-08	Leakage inductance of asynchronous motor	0.01mH~655.35H (frequency converter power ≤ 55kW) 0.001mH~65.535mH (frequency converter power>55kW)	Tuning parameters	★
P1-09	Asynchronous motor mutual inductance	0.1mH~6553.5mH (frequency converter power ≤ 55kW) 0.01mH~655.35H (frequency converter power>55kW)	Tuning parameters	★
P1-10	Asynchronous motor no-load current	0.01A~P1-03 (inverter power ≤ 55kW) 0.1A~P1-03 (inverter power>55kW)	Tuning parameters	★
P1-27	encoder line count	1~65535	one thousand and twenty-four	★
P1-28	Speed fbk sel	0: ABZ incremental encoder 2: Rotating Transformer	0	★
P1-30	ABZ incremental encoder AB phase sequence	0: Positive 1: Reverse direction	0	★
P1-34	Number of poles of rotary transformer	1~65535	one	★
P1-36	Speed feedback PG disconnection Detection Time	0.0s: No action 0.1s~10.0s
P1-37	Tuning selection	0: No operation 1: Parameter tuning of the static part of asynchronous machine 2: Asynchronous machine dynamic complete tuning 3: Asynchronous machine static complete tuning 11: Synchronize complete tuning	0	★
P2 group first motor vector control parameter group
P2-00	Speed loop proportional gain 1	1~100	thirty	☆
P2-01	Speed loop integration time 1	0.01s~10.00s	0.50s	☆
P2-02	Switching frequency 1	0.00~P2-05	5.00Hz	☆
P2-03	Speed loop proportional gain 2	1~100	twenty	☆
P2-04	Speed loop integration time 2	0.01s~10.00s	1.00s	☆
P2-05	Switching frequency 2	P2-02~Maximum frequency	10.00Hz	☆
P2-06	Vector control slip gain	50%~200%	100%	☆
P2-07	SVC speed Feedback filtering time	0.000s~0.100s	0.015s	☆
P2-09	Under speed control mode Selection of torque upper limit command	0: Parameter P2-10 setting 1：AI1 2：AI2 3：AI3 4: Pulse (DI5) 5: Communication given 6：MIN(AI1,AI2) 7：MAX(AI1,AI2) The full range of options 1-7 corresponds to P2-10	0	☆
P2-10	Numerical setting of torque upper limit under speed control mode	0.0%~200.0%	150%	☆
P2-11	Under speed control mode Torque upper limit command selection (power generation)	0: Parameter P2-10 setting (without distinguishing between electric and power generation) 1：AI1 2：AI2 3：AI3 4: PULSE pulse setting 5: Communication given 6：MIN(AI1,AI2) 7：MAX(AI1,AI2) 8: Parameter P2-12 setting The full range of options 1-7 corresponds to P2-12	0	☆
P2-12	Under speed control mode Torque upper limit digital setting (power generation)	0.0% ~ 200.0%	150%	☆
P2-13	Excitation regulation Proportional gain	0~60000	two thousand	☆
P2-15	Torque regulation Proportional gain	0~60000	two thousand	☆
P2-16	Torque regulation Integral gain	0~60000	one thousand and three hundred	☆
P2-17	Integral attribute of speed loop	Individual position: Integral separation 0: Invalid 1: Effective	0	☆
P2-21	Maximum in the weak magnetic region Torque coefficient	50~200%	100%	☆
P2-22	power generation capacity Restricted enablement	0: Invalid 1: Effective throughout the entire process 2: Constant speed effectiveness 3: Deceleration takes effect	0	☆
P3 group V/F control parameter group
P3-00	V/F curve setting	0: Straight line V/F 1: Multi point V/F 2: Square V/F 3: 1.2 square V/F 4: 1.4 square V/F 6: 1.6 square V/F 8: 1.8 square V/F 9: Reserved 10: V/F complete separation mode 11: V/F semi separation mode	0	★
P3-01	Torque increase	0.0%: (Automatic torque boost) 0.1%~30.0%	Model determination	☆
P3-02	Torque increase cut-off frequency	0.00Hz~maximum frequency	50.00Hz	★
P3-03	Multi point V/F frequency point 1	0.00Hz~ P3-05	0.00Hz	★
P3-04	Multi point V/F voltage point 1	0.0%~100.0%	0%	★
P3-05	Multi point V/F frequency point 2	P3-03~P3-07	0.00Hz	★
P3-06	Multi point V/F voltage point 2	0.0%~100.0%	0%	★
P3-07	Multi point V/F frequency point 3	P3-05~Rated frequency of motor (P1-04)	0.00Hz	★
P3-08	Multi point V/F voltage point 3	0.0%~100.0%	0%	★
P3-10	V/F overexcitation gain	0~200	sixty-four	☆
P3-11	V/F oscillation suppression gain	0~100	forty	☆
P3-13	Voltage source separated by V/F	0: Numerical setting (P3-14) 1：AI1 2：AI2 3：AI3 4: PULSE pulse setting (DI5) 5: Multi segment instruction 6: Simple PLC 7：PID 8: Communication given Note: 100.0% corresponds to the rated voltage of the motor	0	☆
P3-14	Voltage separated by V/F Number setting	0V~Rated voltage of motor	0V	☆
P3-15	Voltage separated by V/F accelerate time	0.0s~1000.0s Note: Refers to the time it takes for 0V to change to the rated voltage of the motor	0.0s	☆
P3-16	Voltage separated by V/F deceleration time	0.0s~1000.0s Note: Refers to the time it takes for 0V to change to the rated voltage of the motor	0.0s	☆
P3-17	V/F separation Selection of shutdown mode	0: Frequency/voltage independently reduced to 0 1: After reducing the voltage to 0, the frequency decreases again	0	☆
P3-18	Overcurrent stall action current	50~200%	150%	★
P3-19	Enable overcurrent stall	0: Invalid 1: Effective	one	★
P3-20	Overcurrent stall suppression gain	0~100	twenty	☆
P3-21	Double speed overcurrent stall action Current compensation coefficient	50~200%	50%	★
P3-22	Overvoltage stall action voltage	Three phase 380~480V models: 30.0V~800.0V Three phase 200~240V model: 30.0V~800.0V		★
P3-23	Overpressure stall enable	0: Invalid 1: Effective	one	★
P3-24	Overpressure stall Suppress frequency gain	0~100	thirty	☆
P3-25	Overpressure stall Suppress voltage gain	0~100	thirty	☆
P3-26	Maximum overvoltage stall Rising frequency limit	0~50Hz	5Hz	★
P4 input terminal parameter group
P4-00	DI1 terminal function selection	0: No functionality 1: Forward running FWD or running command 2: Reverse running REV or forward and reverse running direction 3: Three line operation control 4: Forward turning jog (F JOG) 5: Reverse Jog (R JOG) 6: Terminal UP 7: Terminal Down 8: Free Parking 9: Fault reset (RESET) 10: Pause operation 11: External fault normally open input 12: Multi segment instruction terminal 1 13: Multi segment instruction terminal 2 14: Multi segment instruction terminal 3 15: Multi segment instruction terminal 4 16: Acceleration and deceleration time selection terminal 1 17: Acceleration and deceleration time selection terminal 2 18: Frequency command switching 19: UP/DOWN reset (terminals, keyboard) 20: Control command switching terminal 1 21: Acceleration and deceleration are prohibited 22: PID pause 23: Simple PLC state reset 24: Swing frequency pause 25: Counter input 26: Counter reset 27: Length Count Input 28: Length reset 29: Torque control prohibited 30: Pulse frequency input (only valid for DI5) 31: Reserved 32: Immediate DC braking 33: External fault normally closed input 34: Frequency modification enable 35: PID action direction is reversed 36: External parking terminal 1	one	★
P4-01	DI2 terminal function selection		two	★
P4-02	DI3 terminal function selection		three	★
P4-03	DI4 terminal function selection		twelve	★
P4-04	DI5 terminal function selection		thirteen	★
P4-05	DI6 terminal function selection		0	★
P4-06	DI7 terminal function selection (expansion board)	37: Control command switching terminal 2 38: PID points suspended 39: Switching between main frequency and preset frequency 40: Switching between auxiliary frequency and preset frequency 41: Motor terminal selection function 42: Reserved 43: PID parameter switching 44: User defined fault 1 45: User defined fault 2 46: Switching between speed control and torque control 47: Emergency stop 48: External parking terminal 2 49: Deceleration DC braking 50: This run time is reset to zero 51: Two wire/three wire switching 52: Reverse frequency prohibition 53-59: Reserved	0	★
P4-07	DI8 terminal function selection (expansion board)		0	★
P4-08	DI9 terminal function selection (expansion board)		0	★
P4-09	DI10 terminal function selection (expansion board)		0	★
P4-10	DI filtering time	0.000s~1.000s	0.010s	☆
P4-11	Terminal command method	0: Two line type 1 1: Two line type 2 2: Three line type 1 3: Three line type 2	0	★
P4-12	Terminal UP/DOWN rate of change	0.001Hz/s~65.535Hz/s	1.00Hz/s	☆
P4-13	AI curve 1 minimum input	0.00V~P4-15	0.00V	☆
P4-14	AI curve 1 minimum input Corresponding settings	-100.0%~+100.0%	0%	☆
P4-15	AI curve 1 maximum input	P4-13~+10.00V	10.00V	☆
P4-16	AI curve 1 maximum input Corresponding settings	-100.0%~+100.0%	100%	☆
P4-17	AI1 filtering time	0.00s~10.00s	0.10s	☆
P4-18	AI curve 2 minimum input	0.00V~P4-20	0.00V	☆
P4-19	AI curve 2 minimum input Corresponding settings	-100.0%~+100.0%	0%	☆
P4-20	AI curve 2 maximum input	P4-18~+10.00V	10.00V	☆
P4-21	AI curve 2 maximum input Corresponding settings	-100.0%~+100.0%	100%	☆
P4-22	AI2 filtering time	0.00s~10.00s	0.10s	☆
P4-23	AI Curve 3 Minimum Input	-10.00V~P4-25	-10.00V	☆
P4-24	AI Curve 3 Minimum Input Corresponding settings	-100.0%~+100.0%	-100.0%	☆
P4-25	AI curve 3 maximum input	P4-23~+10.00V	10.00V	☆
P4-26	AI curve 3 maximum input Corresponding settings	-100.0%~+100.0%	100%	☆
P4-27	AI3 filtering time	0.00s~10.00s	0.10s	☆
P4-28	Minimum frequency of pulse input	0.00kHz~P4-30	0.00kHz	☆
P4-29	Minimum input frequency of pulse Corresponding settings	-100.0%~100.0%	0%	☆
P4-30	Maximum input frequency of pulse	P4-28~100.00kHz	50.00kHz	☆
P4-31	Maximum input frequency of pulse Corresponding settings	-100.0%~100.0%	100%	☆
P4-32	Pulse filtering time	0.00s~10.00s	0.10s	☆
P4-33	AI curve selection	Individual position: AI1 curve selection 1: Curve 1 (2 points, see P4-13~P4-16) 2: Curve 2 (2 points, see P4-18~P4-21) 3: Curve 3 (2 points, see P4-23~P4-26) 4: Curve 4 (4 points, see A6-00~A6-07) 5: Curve 5 (4 points, see A6-08~A6-15) Tenth digit: AI2 curve selection, as above Hundred digit: AI3 curve selection, as above	three hundred and twenty-one	☆
P4-34	AI below minimum input setting Choose a specific option	Position: AI1 is below the minimum input setting selection 0: Corresponding minimum input setting 1：0.0% Ten digit: AI2 is lower than the minimum input setting selection, as above Hundred digit: AI3 below the minimum input setting selection, as above	000	☆
P4-35	DI1 delay time	0.0s~3600.0s	0.0s	★
P4-36	DI2 delay time	0.0s~3600.0s	0.0s	★
P4-37	DI3 delay time	0.0s~3600.0s	0.0s	★
P4-38	DI terminal effective mode Choose 1	0: High level effective 1: Low level effective Position: DI1 Ten digits: DI2 Hundred digit: DI3 Thousand digits: DI4 10000 positions: DI5	00000	★
P4-39	DI terminal effective mode Choose 2	0: High level effective 1: Low level effective bits: DI6 Tenth digit: DI7 Hundred digits: DI8 Thousand digits: DI9 10000 positions: DI10	00000	★
P5 output terminal parameter group
P5-00	FM terminal output mode choice	0: Pulse output (FMP) 1: Switching output (FMR)	0	☆
P5-01	FM Function Selection (Set) Open circuit electrode output terminal Child)	0: No output 1: Inverter in operation 2: Fault output (for free stop faults) 3: Frequency level detection 1 4: Frequency arrival 5: Zero speed operation (no output during shutdown) 6: Motor overload warning 7: Inverter overload warning 8: Set the record value to arrive 9: The specified record value has been reached 10: Length reached 11: Simple PLC cycle completion 12: Accumulated running time reached 13: Under frequency limitation 14: Torque limitation 15: Ready for operation 16：AI1>AI2 17: The upper limit frequency has been reached 18: Lower limit frequency reached (no output during shutdown)	0	☆
P5-02	Relay 1 Function Selection (T1A-T1B-T1C)		one	☆
P5-03	Relay 2 Function Selection （ T2A-T2B-T2C ）		two	☆
P5-04	DO1 output function selection	19: Under voltage state 20: Communication settings 21: Reserved 22: Reserved 23: Zero speed operation 2 (also output when stopped) 24: Accumulated power on time reached 25: Frequency level detection 2 26: Frequency 1 has arrived 27: Frequency 2 arrived 28: Current 1 arrives 29: Current 2 arrives 30: Scheduled arrival 31: AI1 input exceeds the limit 32: Falling load 33: Running in reverse 34: Zero current state 35: The module temperature has reached 36: Output current exceeds the limit 37: The lower limit frequency has been reached (output even when stopped) 38: Alarm (all faults) 39: Motor overheating 40: The current running time has arrived 41: Fault (free stop fault and under voltage not outputting)	0	☆
P5-05	Expansion card DO2 output Function Selection		four	☆
P5-06	FMP output function selection	0: Operating frequency 1: Set frequency 2: Output current 3: Motor output torque (absolute value, percentage relative to the motor) 4: Output power 5: Output voltage 6: Pulse input (100.0% corresponds to 100.0kHz)	0	☆
P5-07	AO1 output function selection	7：AI1 8：AI2 9: Panel potentiometer 10: Length 11: Record numerical values 12: Communication settings 13: Motor speed 14: Output current (100.0% corresponds to 1000.0A) 15: Output voltage (100.0% corresponds to 1000.0V) 16: Motor output torque (actual value, percentage relative to the motor) FMP output function selection	0	☆
P5-08	AO2 output function selection		four	☆
P5-09	FMP output maximum frequency	0.01kHz~100.00kHz	50.00kHz
P5-10	AO1 zero bias coefficient	-100.0%~+100.0%	0%
P5-11	AO1 gain	-10.00~+10.00	one
P5-12	AO2 zero bias coefficient	-100.0%~+100.0%	0%
P5-13	AO2 gain	-10.00~+10.00	one
P5-17	FM output delay time	0.0s~3600.0s	0.0s
P5-18	RELAY1 output delay time	0.0s~3600.0s	0.0s
P5-19	RELAY2 output delay time	0.0s~3600.0s	0.0s
P5-20	DO1 output delay time	0.0s~3600.0s	0.0s
P5-21	DO2 output delay time	0.0s~3600.0s	0.0s
P5-22	DO output terminal is valid Status selection	0: Positive Logic 1: Anti logical position: FMR Tenth digit: RELAY1 Hundreds: RELAY2 Thousand positions: DO1 10000 positions: DO2	00000
P6 group start stop control parameter group
P6-00	Startup method	0: Directly start 1: Speed tracking restart 2: Pre excitation start (AC asynchronous machine) 3: SVC Quick Start	0	☆
P6-01	Speed tracking method	0: Starting from the shutdown frequency 1: Starting from the power frequency 2: Starting from the maximum frequency	0	★
P6-02	Speed tracking speed	1~100	twenty	☆
P6-03	Startup frequency	0.00Hz~10.00Hz	0.00Hz	☆
P6-04	Start frequency holding time	0.0s~100.0s	0.0s	★
P6-05	Start DC braking current/pre excitation current	0%~100%	50%	★
P6-06	Start DC braking time/pre excitation time	0.0s~100.0s	0.0s	★
P6-07	Acceleration and deceleration methods	0: Linear acceleration and deceleration 1: Static S-curve 2: Dynamic S-curve acceleration and deceleration	0	★
P6-08	Starting segment of S-curve Time proportion	0.0%~(100.0%-P6-09)	30%	★
P6-09	End segment of S-curve Time proportion	0.0%~(100.0%-P6-08)	30%	★
P6-10	shutdown method	0: Slow down parking 1: Free parking	0	☆
P6-11	Shutdown DC brake Starting frequency	0.00Hz~maximum frequency	0.00Hz	☆
P6-12	Shutdown DC brake waiting time	0.0s~100.0s	0.0s	☆
P6-13	Shutdown DC brake current	0%~100%	50%	☆
P6-14	Shutdown DC braking time	0.0s~100.0s	0.0s	☆
P6-15	Brake utilization rate	0%~100%	100%	☆
P6-18	Speed tracking current magnitude	30%~200%	Model determination	★
P6-21	Demagnetization time (SVC is effective)	0.00~5.00s	Model determination	☆
P6-23	Overexcitation selection	0: Not effective 1: Only deceleration takes effect 2: Effective throughout the entire process	0	☆
P6-24	Overexcitation suppression current value	0~150%	100%	☆
P6-25	Overexcitation gain	1.00~2.50	one point two five	☆
P7 keyboard and display parameter group
P7-00	Digital tube missing picture inspection enable	0~1	0	☆
P7-01	MF. K key function selection	0: MF. K is invalid 1: Switching between operation panel command channel and remote command channel (terminal command channel or communication command channel) 2: Forward and reverse switching 3: Forward turning jog 4: Reverse jog	0	★
P7-02	STOP/RESET Key function	0: The STOP/RES key shutdown function is only valid in keyboard operation mode 1: The STOP/RES button shutdown function is valid in any operating mode	one	☆
P7-03	LED1 operation Display parameter 1	0000~FFFF Bit00: Operating frequency 1 (Hz) Bit01: Set frequency (Hz) Bit02: Bus voltage (V) Bit03: Output voltage (V) Bit04: Output current (A) Bit05: Output power (kW) Bit06: Output torque (%) Bit07: DI input status Bit08: DO output status Bit09: AI1 voltage (V) Bit10: AI2 voltage (V) Bit11: AI3 voltage (V) Bit12: Count value Bit13: Length value Bit14: Load speed display Bit15: PID setting	1F	☆
P7-04	LED1 operation Display parameter 2	0000~FFFF Bit00: PID feedback Bit01: PLC Stage Bit02: PULSE input pulse frequency kHz Bit03: Operating frequency 2 (Hz) Bit04: Remaining running time Bit05: AI1 pre calibration voltage (V) Bit06: AI2 pre calibration voltage (V) Bit07: Voltage before AI3 calibration (V) Bit08: Motor speed Bit09: Current power on time (Hour) Bit10: Current running time (Min) Bit11: Pulse input frequency (Hz) Bit12: Communication settings Bit13: Encoder feedback speed (Hz) Bit14: Main frequency X display (Hz) Bit15: Auxiliary frequency Y display (Hz)	0	☆
P7-05	LED1 shutdown display parameters	0000~FFFF Bit00: Set frequency (Hz) Bit01: Bus voltage (V) Bit02: DI input status Bit03: DO output status Bit04: AI1 voltage (V) Bit05: AI2 voltage (V) Bit06: AI3 voltage (V) Bit07: Count value Bit08: Length value Bit09: PLC Stage Bit10: Load speed Bit11: PID setting Bit12: PULSE input pulse frequency kHz	thirty-three	☆
P7-06	Load transmission ratio	0.001~65.000	two point nine two	☆
P7-07	Inverter module Temperature of radiator	-20℃ ~120℃	-	●
P7-08	Product Number	-	-	●
P7-09	Accumulated running time	0h~65535h	-	●
P7-10	Performance version number	-	-	●
P7-11	Function version number	-	-	●
P7-12	load speed Display decimal place	Number of decimal points: U0-14 0:0 decimal places 1: One decimal place 2: Two decimal places Ten digits: U0-19/U0-29 decimal points 1: One decimal place 2: Two decimal places	twenty	☆
P7-13	Accumulated power on time	0~65535 hours	-	●
P7-14	Accumulated power consumption	0~65535 degrees	-	●
P7-17	LED2 shutdown display parameters	U0-00~U0-75	two	★
P7-18	LED2 operation display parameters	U0-00~U0-75	two	★
P8 auxiliary function parameter group
P8-00	Jogging operating frequency	0.00Hz~maximum frequency	2.00Hz	●
P8-01	Jogging acceleration time	0.0s~6500.0s	20.0s
P8-02	Jogging deceleration time	0.0s~6500.0s	20.0s
P8-03	Acceleration time 2	0.00s~650.00s ( P0-19=2 ) 0.0s~6500.0s ( P0-19=1 ) 0s~65000s ( P0-19=0 )	Model determination
P8-04	Deceleration time 2	0.00s~650.00s ( P0-19=2 ) 0.0s~6500.0s ( P0-19=1 ) 0s~65000s ( P0-19=0 )	Model determination
P8-05	Acceleration time 3	0.00s~650.00s ( P0-19=2 ) 0.0s~6500.0s ( P0-19=1 ) 0s~65000s ( P0-19=0 )	Model determination
P8-06	Deceleration time 3	0.00s~650.00s ( P0-19=2 ) 0.0s~6500.0s ( P0-19=1 ) 0s~65000s ( P0-19=0 )	Model determination
P8-07	Acceleration time 4	0.00s~650.00s ( P0-19=2 ) 0.0s~6500.0s ( P0-19=1 ) 0s~65000s ( P0-19=0 )	0.0s
P8-08	Deceleration time 4	0.00s~650.00s ( P0-19=2 ) 0.0s~6500.0s ( P0-19=1 ) 0s~65000s ( P0-19=0 )	0.0s	☆
P8-09	Received data gain (frequency)	-10.00~10.00	one	☆
P8-10	Jump frequency 2	0.00Hz~maximum frequency	0.00Hz	☆
P8-11	Jump frequency amplitude	0.00Hz~maximum frequency	0.00Hz	☆
P8-12	Dead time of forward and reverse rotation	0.0s~3000.0s	0.0s	☆
P8-13	Reverse frequency prohibition	0: Invalid 1: Valid	0	☆
P8-14	Set the operating mode with a frequency lower than the lower limit frequency	0: Running at the lower limit frequency 1: Shutdown 2: Zero speed operation	0	☆
P8-15	Sag rate	0.00%~100.00%	0%	☆
P8-16	Set the cumulative power on arrival time	0h~65000h	0h	☆
P8-17	Set the cumulative running arrival time	0h~65000h	0h	☆
P8-18	Activate protection selection	0: Not protected 1: Protected	0	☆
P8-19	Frequency detection value 1	0.00Hz~maximum frequency	50.00Hz	☆
P8-20	Frequency detection lag rate 1	0.0%~100.0% (FDT1 level)	5%	☆
P8-21	Frequency reaches the detected amplitude	0.0%~100.0% (maximum frequency)	0%	☆
P8-22	Is the jumping frequency effective during acceleration and deceleration	0: Invalid 1: Effective	0	☆
P8-25	Switching frequency points between acceleration time 1 and acceleration time 2	0.00Hz~maximum frequency	0.00Hz	☆
P8-26	Switching frequency points between deceleration time 1 and deceleration time 2	0.00Hz~maximum frequency	0.00Hz	☆
P8-27	Terminal jog priority	0: Invalid 1: Valid	0	☆
P8-28	Frequency detection value 2	0.00Hz~maximum frequency	50.00Hz	☆
P8-29	Frequency detection lag rate 2	0.0%~100.0% (FDT2 level)	5%	☆
P8-30	Any frequency of arrival Detection value 1	0.00Hz~maximum frequency	50.00Hz	☆
P8-31	Any frequency of arrival Detection amplitude 1	0.0%~100.0% (maximum frequency)	0%	☆
P8-32	Any frequency of arrival Detection value 2	0.00Hz~maximum frequency	50.00Hz	☆
P8-33	Any frequency of arrival Detection amplitude 2	0.0%~100.0% (maximum frequency)	0%	☆
P8-34	Zero current detection level	0.0%~300.0% 100.0% corresponds to the rated current of the motor	5%	☆
P8-35	Zero current detection delay time	0.01s~600.00s	0.10s	☆
P8-36	Output current exceeds the limit value	0.0% (not detected) 0.1%~300.0% (rated current of motor)	200%	☆
P8-37	Output current exceeds the limit Detecting delay time	0.00s~600.00s	0.00s	☆
P8-38	Any current reaching 1	0.0%~300.0% (rated current of motor)	100%	☆
P8-39	Arrive arbitrarily Current amplitude 1	0.0%~300.0% (rated current of motor)	0%	☆
P8-40	Any current reaching 2	0.0%~300.0% (rated current of motor)	100%	☆
P8-41	Arrive arbitrarily Current amplitude 2	0.0%~300.0% (rated current of motor)	0%	☆
P8-42	Timer function selection	0: Invalid 1: Valid	0	★
P8-43	Timed running time selection	0: P8-44 setting 1：AI1 2：AI2 3：AI3 Analog input range corresponds to P8-44	0	★
P8-44	Timed running time	0.0Min~6500.0Min	0.0Min	★
P8-45	AI1 input voltage Lower limit of protection value	0.00V~P8-46	3.10V	☆
P8-46	AI1 input voltage Protection value upper limit	P8-45~10.00V	6.80V	☆
P8-47	The module temperature has reached	0℃ ~100℃	75℃	☆
P8-48	Cooling fan control	0: Fan running during operation 1: The fan keeps running	0	☆
P8-49	Wake up frequency	Sleep frequency (P8-51)~ Maximum frequency (P0-10)	0.00Hz	☆
P8-50	Wake up delay time	0.0s~6500.0s	0.0s	☆
P8-51	Sleep frequency	0.00Hz~wake-up frequency (P8-49)	0.00Hz	☆
P8-52	Sleep delay time	0.0s~6500.0s	0.0s	☆
P8-53	Arrival time of this run	0.0~6500.0 minutes	0.0Min	☆
P8-54	Output power correction coefficient	0.00%~200.0%	100%	☆
P8-55	Emergency stop deceleration time	0~6553.5	Model determination	☆
P9 Fault and Protection Parameter Group
P9-00	Selection of motor overload protection	0: Prohibit 1: Allow	one	☆
P9-01	Motor overload protection gain	0.20~10.00	one	☆
P9-02	Motor overload warning coefficient	50%~100%	80%	☆
P9-03	Overvoltage stall gain	0~100	thirty	☆
P9-04	Overvoltage stall protection voltage	650V~800V	770V	☆
P9-07	Selection of ground short circuit protection	Position: Selection of short-circuit protection for power on to ground 0: Invalid 1: Valid Ten digit: Selection of ground short circuit protection before operation 0: Invalid 1: Valid	01	☆
P9-08	Braking unit action starting voltage	Three phase 380~480V models: 330.0V~800.0V Three phase 200~240V model: 330.0V~800.0V		★
P9-09	Number of automatic fault resets	0~20	0	☆
P9-10	During the automatic fault reset period Fault DO action selection	0: No action 1: Action	0	☆
P9-11	Fault automatic reset waiting time	0.1s~100.0s	1.0s	☆
P9-12	Input phase loss contactor Suction protection selection	Position: Input phase loss protection selection 0: Prohibit input phase loss protection 1: Protection when both software and hardware input phase loss conditions are met simultaneously 2: Protect as long as the software input phase loss condition is met 3: Protect as long as the hardware input phase loss condition is met Ten digit: contactor suction protection selection 0: Prohibit 1: Allow	eleven	☆
P9-13	Phase loss protection selection	Position: Output phase loss protection selection 0: Prohibit 1: Allow Ten digit: Selection of output phase loss protection before operation 0: Prohibit 1: Allow	01	☆
P9-14	First fault type	0: No malfunction 1: Reserved 2: Accelerated overcurrent 3: Deceleration overcurrent 4: Constant speed overcurrent 5: Accelerated overvoltage 6: Deceleration overvoltage 7: Constant speed overvoltage 8: Buffer resistor overload 9: Undervoltage 10: Inverter overload 11: Motor overload 12: Input phase loss 13: Output phase loss 14: Module overheating 15: External malfunction 16: Communication abnormality 17: Abnormal contactor 18: Abnormal current detection 19: Abnormal motor tuning 20: Encoder/PG card abnormality 21: Parameter read/write exception 22: Hardware abnormality of frequency converter 23: Motor short circuit to ground 24: Reserved 25: Reserved 26: The running time has arrived 27: User defined fault 1 28: User defined fault 2 29: The power on time has arrived 30: Load shedding 31: PID feedback lost during runtime 40: Fast current limiting timeout 41: Switching motors during operation 42: Excessive speed deviation 43: Motor overspeed 45: Motor overheating 51: Initial position error 55: Slave failure during master-slave control	-	●
P9-15	Second fault type		-	●
P9-16	Third fault type		-	●
P9-17	Third time (most recent) Frequency during malfunction	0.00Hz~655.35Hz	0.00Hz	●
P9-18	Third time (most recent) Current during malfunction	0.00A~655.35A	0.00A	●
P9-19	Third time (most recent) Bus voltage during malfunction	0.0V~6553.5V	0.0V	●
P9-20	Third time (most recent) Input terminal status during malfunction	0~9999	0	●
P9-21	Third time (most recent) Output terminal status during malfunction	0~9999	0	●
P9-22	Third time (most recent) Inverter status during malfunction	0~65535	0	●
P9-23	Third time (most recent) Power on time during malfunction	0s~65535s	0s	●
P9-24	Third time (most recent) Running time during malfunction	0.0s~6553.5s	0.0s	●
P9-27	Frequency during the second malfunction	0.00Hz~655.35Hz	0.00Hz	●
P9-28	Current during the second fault	0.00A~655.35A	0.00A	●
P9-29	Bus voltage during the second fault	0.0V~6553.5V	0.0V	●
P9-30	During the second malfunction Input terminal status	0~9999	0	●
P9-31	During the second malfunction Output terminal status	0~9999	0	●
P9-32	During the second malfunction Inverter status	0~65535	0	●
P9-33	Power on time during the second malfunction	0s~65535s	0s	●
P9-34	Running time during the second malfunction	0.0s~6553.5s	0.0s	●
P9-37	Frequency during the first malfunction	0.00Hz~655.35Hz	0.00Hz	●
P9-38	Current during the first malfunction	0.00A~655.35A	0.00A	●
P9-39	Bus voltage during the first malfunction	0.0V~6553.5V	0.0V	●
P9-40	During the first malfunction Input terminal status	0~9999	0	●
P9-41	During the first malfunction Output terminal status	0~9999	0	●
P9-42	During the first malfunction Inverter status	0~65535	0	●
P9-43	Power on time during the first malfunction	0s~65535s	0s	●
P9-44	Running time during the first malfunction	0.0s~6553.5s	0.0s	●
P9-47	Fault protection action selection 1	Position: Motor overload (Err11) 0: Free Parking 1: Stop the machine according to the shutdown method 2: Continue running Ten digits: Input missing phase (Err12) Hundred bit: Output phase loss (Err13) Thousand digit: External fault (Err15) Ten thousand digits: Communication abnormality (Err16)	00000	☆
P9-48	Fault protection action selection 2	Position: Encoder/PG card abnormal (Err20) 0: Free parking Ten digits: Parameter read/write exception (Err21) 0: Free Parking 1: Stop the machine according to the shutdown method Hundred digit: Action selection for frequency converter overload fault (Err10) 0: Free shutdown 1: Reduced operation Thousand position: Motor overheating (Err45) Ten thousand digits: The running time has reached (Err26)	00000	☆
P9-49	Fault protection Action selection 3	Individual position: User defined fault 1 (27) 0: Free Parking 1: Stop the machine according to the shutdown method 2: Continue running Ten digits: User defined fault 2 (28) 0: Free Parking 1: Stop the machine according to the shutdown method 2: Continue running Hundred digits: Power on time reached (29) 0: Free Parking 1: Stop the machine according to the shutdown method 2: Continue running Thousand positions: Load shedding (30) 0: Free Parking 1: Slow down and stop 2: Jump directly to 7% of the rated frequency of the motor to continue running, and automatically return to the set frequency when there is no load drop Ten thousand bits: PID feedback lost during runtime (31) 0: Free Parking 1: Stop the machine according to the shutdown method 2: Continue running	00000	☆
P9-50	Fault protection action Choose 4	Position: Excessive speed deviation (42) 0: Free Parking 1: Stop the machine according to the shutdown method 2: Continue running Tenth digit: Motor overspeed (43) Hundred digit: Initial position error (51)	00000	☆
P9-54	Continue operation in case of malfunction Frequency selection	0: Run at the current operating frequency 1: Run at the set frequency 2: Operate at the upper limit frequency 3: Operate at the lower limit frequency 4: Operating at an abnormal backup frequency	0	☆
P9-55	Abnormal backup frequency	0.0%~100.0% (100.0% corresponds to maximum frequency P0-10)	100%	☆
P9-56	Motor temperature sensor type	0: No temperature sensor 1：PT100 2：PT1000	0	☆
P9-57	Motor overheat protection threshold	0℃ ~200℃	110℃	☆
P9-58	Motor overheating warning threshold	0℃ ~200℃	90℃	☆
P9-59	Instant stop function selection	0: Invalid 1: Bus voltage constant control 2: Slow down and stop the machine 3: Vibration suppression	0	★
P9-60	Instantly stop and continuously restore voltage	80%~100%	85%	★
P9-61	Instant non-stop voltage recovery judge the time	0.0~100.0s	0.5S	★
P9-62	Instantaneous non-stop action voltage	60%~100%	80%	★
P9-63	Load drop protection selection	0: Invalid 1: Effective	0	☆
P9-64	Load drop detection level	0.0~100.0%	10%	☆
P9-65	Load drop detection time	0.0~60.0s	1.0s	☆
P9-67	Speed detection value	0.0%~50.0% (maximum frequency)	20%	☆
P9-68	Speed detection time	0.0s: No detection 0.1~60.0s	1.0s	☆
P9-69	Detection value for excessive speed deviation	0.0%~50.0% (maximum frequency)	20%	☆
P9-70	Detection time for excessive speed deviation	0.0s: No detection 0.1~60.0s	5.0s	☆
P9-71	Instant non-stop gain Kp	0~100	forty	☆
P9-72	Instant non-stop integration coefficient Ki	0~100	thirty	☆
P9-73	Instant stop non-stop action deceleration time	0~300.0s	20.0s	★
PA group PID functional parameter group
PA-00	PID given source	0: PA-01 setting 1：AI1 2：AI2 3：AI3 4: Pulse setting (DI5) 5: Communication given 6: Multi segment instruction given	0	☆
PA-01	PID value given	0.0%~100.0%	50%	☆
PA-02	PID feedback source	0：AI1 1：AI2 2：AI3 3：AI1-AI2 4: Pulse setting (DI5) 5: Communication given 6：AI1+AI2 7：MAX(\|AI1\|,\|AI2\|) 8：MIN(\|AI1\|,\|AI2\|)	0	☆
PA-03	PID action direction	0: Positive effect 1: Negative effect	0	☆
PA-04	PID given feedback range	0~65535	one thousand	☆
PA-05	Proportional gain KP1	0.0~1000.0	twenty	☆
PA-06	Integral time TI1	0.01s~10.00s	2.00s	☆
PA-07	Differential time TD1	0.000s~10.000s	0.000s	☆
PA-08	PID inversion cut-off frequency	0.00~maximum frequency	0.00Hz	☆
PA-09	PID deviation limit	0.0%~100.0%	0%	☆
PA-10	PID differential limiting	0.00%~100.00%	0.10%	☆
PA-11	PID given change time	0.00~650.00s	0.00s	☆
PA-12	PID feedback filtering time	0.00~60.00s	0.00s	☆
PA-13	PID output filtering time	0.00~60.00s	0.00s	☆
PA-14	retain	-	-	☆
PA-15	Proportional gain KP2	0~1000.0	twenty	☆
PA-16	Integral time TI2	0.01s~10.00s	2.00s	☆
PA-17	Differential time TD2	0.000s~10.000s	0.000s	☆
PA-18	PID parameter switching conditions	0: Do not switch 1: Switching through DI terminal 2: Automatically switch based on deviation 3: Automatically switch based on operating frequency	0	☆
PA-19	PID parameter switching deviation 1	0.0%~PA-20	20%	☆
PA-20	PID parameter switching deviation 2	PA-19~100.0%	80%	☆
PA-21	PID initial value	0.0%~100.0%	0%	☆
PA-22	PID initial value retention time	0.00~650.00s	0.00s	☆
PA-25	PID integral attribute	Individual position: Integral separation 0: Invalid 1: Valid Ten digits: whether to stop integrating after outputting to the limit value 0: Continue to accumulate points 1: Stop accumulating points	00	☆
PA-26	PID feedback loss detection value	0.0%: Feedback loss without judgment 0.1%~100.0%	0%	☆
PA-27	PID feedback loss Detection Time	0.0s~20.0s	0.0s	☆
PA-28	PID shutdown calculation	0: Shutdown without calculation 1: Calculation during shutdown	0	☆
PC group multi segment instructions, simple PLC parameter group
PC-00	Multi segment instruction 0	-100.0%~100.0%	0%	☆
PC-01	Multi segment instruction 1	-100.0%~100.0%	0%	☆
PC-02	Multi segment instruction 2	-100.0%~100.0%	0%	☆
PC-03	Multi segment instruction 3	-100.0%~100.0%	0%	☆
PC-04	Multi segment instruction 4	-100.0%~100.0%	0%	☆
PC-05	Multi segment instruction 5	-100.0%~100.0%	0%	☆
PC-06	Multi segment instruction 6	-100.0%~100.0%	0%	☆
PC-07	Multi segment instruction 7	-100.0%~100.0%	0%	☆
PC-08	Multi segment instruction 8	-100.0%~100.0%	0%	☆
PC-09	Multi segment instruction 9	-100.0%~100.0%	0%	☆
PC-10	Multi segment instruction 10	-100.0%~100.0%	0%	☆
PC-11	Multi segment instruction 11	-100.0%~100.0%	0%	☆
PC-12	Multi segment instruction 12	-100.0%~100.0%	0%	☆
PC-13	Multi segment instruction 13	-100.0%~100.0%	0%	☆
PC-14	Multi segment instruction 14	-100.0%~100.0%	0%	☆
PC-15	Multi segment instruction 15	-100.0%~100.0%	0%	☆
PC-16	Simple PLC operation mode	0: Shutdown at the end of a single run 1: Maintain the final value at the end of a single run 2: Continuously looping	0	☆
PC-17	Simple PLC loses power Memory selection	Position: Power down memory selection 0: No memory after power failure 1: Power off memory Ten digit: Shutdown Memory Selection 0: Shutdown without memory 1: Shutdown memory	00	☆
PC-18	Simple PLC Stage 0 Running Time	0.0s(h)~6553.5s(h)	0.0s(h)	☆
PC-19	Simple PLC segment 0 Acceleration and deceleration time selection	0~3	0	☆
PC-20	Simple PLC first stage running time	0.0s(h)~6553.5s(h)	0.0s(h)	☆
PC-21	Simple PLC Section 1 Acceleration and deceleration time selection	0~3	0	☆
PC-22	Simple PLC second stage running time	0.0s(h)~6553.5s(h)	0.0s(h)	☆
PC-23	Simplified PLC, Section 2 Acceleration and deceleration time selection	0~3	0	☆
PC-24	Simple PLC third stage running time	0.0s(h)~6553.5s(h)	0.0s(h)	☆
PC-25	Simple PLC Section 3 Acceleration and deceleration time selection	0~3	0	☆
PC-26	Simple PLC fourth stage running time	0.0s(h)~6553.5s(h)	0.0s(h)	☆
PC-27	Simple PLC, Section 4 Acceleration and deceleration time selection	0~3	0	☆
PC-28	Simple PLC 5th stage running time	0.0s(h)~6553.5s(h)	0.0s(h)	☆
PC-29	Simple PLC 5th paragraph Acceleration and deceleration time selection	0~3	0	☆
PC-30	Simple PLC 6th stage running time	0.0s(h)~6553.5s(h)	0.0s(h)	☆
PC-31	Simplified PLC Section 6 Acceleration and deceleration time selection	0~3	0	☆
PC-32	Simple PLC 7th stage running time	0.0s(h)~6553.5s(h)	0.0s(h)	☆
PC-33	Simple PLC segment 7 Acceleration and deceleration time selection	0~3	0	☆
PC-34	Simple PLC 8th stage running time	0.0s(h)~6553.5s(h)	0.0s(h)	☆
PC-35	Simple PLC segment 8 Acceleration and deceleration time selection	0~3	0	☆
PC-36	Simple PLC 9th stage running time	0.0s(h)~6553.5s(h)	0.0s(h)	☆
PC-37	Simple PLC segment 9 Acceleration and deceleration time selection	0~3	0	☆
PC-38	Simple PLC 10th running time	0.0s(h)~6553.5s(h)	0.0s(h)	☆
PC-39	Simple PLC Section 10 Acceleration and deceleration time selection	0~3	0	☆
PC-40	Simple PLC 11th stage running time	0.0s(h)~6553.5s(h)	0.0s(h)	☆
PC-41	Simple PLC 11th paragraph Acceleration and deceleration time selection	0~3	0	☆
PC-42	Simple PLC 12th segment running time	0.0s(h)~6553.5s(h)	0.0s(h)	☆
PC-43	Simple PLC 12th paragraph Acceleration and deceleration time selection	0~3	0	☆
PC-44	13th running time of simple PLC	0.0s(h)~6553.5s(h)	0.0s(h)	☆
PC-45	Simple PLC 13th paragraph Acceleration and deceleration time selection	0~3	0	☆
PC-46	14th running time of simple PLC	0.0s(h)~6553.5s(h)	0.0s(h)	☆
PC-47	Simple PLC Section 14 Acceleration and deceleration time selection	0~3	0	☆
PC-48	Simple PLC 15th stage running time	0.0s(h)~6553.5s(h)	0.0s(h)	☆
PC-49	Simple PLC paragraph 15 Acceleration and deceleration time selection	0~3	0	☆
PC-50	Simple PLC operating time unit	0: s (seconds) 1: h (hours)	0	☆
PC-51	Multi segment instruction 0 given method	0: Given parameter PC-00 1：AI1 2：AI2 3：AI3 4: Pulse 5：PID 6: Given preset frequency (P0-08), UP/DOWN can be modified	0	☆
Pd group communication parameter group
Pd-00	Baud rate	Position: MODBUS 0：300BPS 1：600BPS 2：1200BPS 3：2400BPS 4：4800BPS 5：9600BPS 6：19200BPS 7：38400BPS 8：57600BPS 9：115200BPS Ten digits: Profibus DP 0：115200BPｓ 1：208300BPｓ 2：256000BPｓ 3：512000Bps Hundred digits: reserved Thousand bits: CANlink baud rate 0：20 1：50 2：100 3：125 4：250 5：500 6：1M	five thousand and five	☆
Pd-01	MODBUS data format	0: No verification (8-N-2) 1: Even verification (8-E-1) 2: Odd verification (8-O-1) 3: No verification (8-N-1) (MODBUS valid)	0	☆
Pd-02	localhost	0: Broadcast address 1~247(Modbus、Profibus-DP、CANlink、Profinet、EtherCAT 有效 )	one	☆
Pd-03	MODBUS response delay	0~20ms (MODBUS valid)	two	☆
Pd-04	Serial communication timeout	0.0: Invalid 0.1~60.0s(Modbus、Profibus-DP、CANopen、Profinet、EtherCAT有效 )	zero	☆
Pd-05	Data transmission format selection	Position: Modbus 0: Non standard Modbus protocol 1: Standard Modbus protocol 十位 :Profibus-DP、CANopen、Profinet、EtherCAT 0: PPO1 format 1: PPO2 format 2: PPO3 format 3: PPO5 format	thirty-one	☆
Pd-06	Communication reading current resolution	0:0.01A (effective when ≤ 55kW) 1：0.1A	0	☆
Pd-08	Profibus DP, CANopen, Profinet, EtherCAT communication interruption detection time	0.0s: Invalid 0.1~60.0s	0	☆
PE group water supply parameter group
PE-00	Sleep pressure deviation	0.0~PE-04	0%	☆
PE-01	Sleep rate	0~10, unit 5Hz/S	02	☆
PE-02	Sleep frequency	0.00Hz~maximum frequency (P0-10)	2.00Hz	☆
PE-03	holding time	000.0~999.9S	two	☆
PE-04	Awaken pressure deviation	0.0~PA-01	5%	☆
PE-05	Wake up delay time	000.0~999.9S	zero	☆
PE-06	Sleep down time	000.0~100.0S	two	☆
PE-07	Selection of water shortage detection methods	0: Not detected 1: Current mode 2: Pressure mode 3: Both types are used	0	☆
PE-08	Water shortage detection pressure	0.0~PA-01	0.5%	☆
PE-09	Water shortage detection frequency	0.00Hz~maximum frequency (P0-10)	5.00Hz	☆
PE-10	Water shortage detection time	000.0~999.9S	five	☆
PE-11	Water shortage detection current	0.01~Rated current of the set model	zero point zero one	☆
PE-12	Automatic water shortage fault Reset interval time	001~100S	fifteen	☆
PE-13	PID high limit alarm set value	0.0%~100%	one hundred	☆
PE-14	PID high limit alarm detection time	000~200S， Set to 0 without alarm	zero	☆
PE-15	PID low limit alarm set value	0.0%~100%	zero	☆
PE-16	PID low limit alarm detection time	000~200S， Set to 0 without alarm	zero	☆
PE-17	Power on automatic operation selection	0: Close 1: Open	0	☆
PE-18	Automatic running delay time	00.1~100S	one	☆
PE-19	Antifreeze function selection	0: Close 1: Open	0	☆
PE-20	Antifreeze cycle	000~9999S， When set to 0, run continuously at the anti freezing operating frequency	0	☆
PE-21	Antifreeze operation time	000~9999S	sixty	☆
PE-22	Antifreeze operating frequency	0.00~30.00Hz	ten
PP group function code management parameter group
PP-00	user password	0~65535	0	☆
PP-01	parameter initialization	0: No operation 01: Restore factory parameters, excluding motor parameters 02: Clear record information 04: Backup the current parameters of the user 501: Restore user backup parameters	0	★
PP-02	Function parameter group display selection	Position: U group display selection 0: Not displayed 1: Display Ten digits: Group A display selection 0: Not displayed 1: Display	eleven	★
PP-03	Personalized parameter group display selection	Individual position: User customized parameter group display selection 0: Not displayed 1: Display Ten: User changes parameter group display selection 0: Not displayed 1: Display	00	☆
PP-04	Parameter modification attribute	0: modifiable 1: Cannot be modified	0	☆

2. Monitoring parameter summary table

parameter	name	minimum unit	Mailing Address
U0 group monitoring parameter table
U0-00	Operating frequency (Hz)	0.01Hz	7000H
U0-01	Set frequency (Hz)	0.01Hz	7001H
U0-02	Bus voltage (V)	0.1V	7002H
U0-03	Output voltage (V)	1V	7003H
U0-04	Output current (A)	0.01A	7004H
U0-05	Output power (kW)	0.1kW	7005H
U0-06	Output torque (%)	0.1%	7006H
U0-07	DI input status	one	7007H
U0-08	DO output status	one	7008H
U0-09	AI1 voltage (V)	0.01V	7009H
U0-10	AI2 voltage (V)/current (mA)	0.01V/0.01mA	700AH
U0-11	AI3 voltage (V)	0.01V	700BH
U0-12	count value	one	700CH
U0-13	length value	one	700DH
U0-14	load speed	1RPM	700EH
U0-15	PID setting	one	700FH
U0-16	PID feedback	one	7010H
U0-17	PLC stage	one	7011H
U0-18	Input pulse frequency (Hz)	0.01kHz	7012H
U0-19	Feedback speed (Hz)	0.01Hz	7013H
U0-20	Remaining running time	0.1Min	7014H
U0-21	AI1 pre calibration voltage	0.001V	7015H
U0-22	AI2 pre calibration voltage (V)/current (mA)	0.001V/0.01mA	7016H
U0-23	AI3 pre calibration voltage	0.001V	7017H
U0-24	Motor speed	1RPM	7018H
U0-25	Current power on time	1Min	7019H
U0-26	Current running time	0.1Min	701AH
U0-27	Input pulse frequency	1Hz	701BH
U0-28	Communication settings	0.01%	701CH
U0-29	Encoder feedback speed	0.01Hz	701DH
U0-30	Main frequency display	0.01Hz	701EH
U0-31	Auxiliary frequency display	0.01Hz	701FH
U0-32	View any memory address value	one	7020H
U0-34	Motor temperature value	1℃	7022H
U0-35	Target torque (%)	0.1%	7023H
U0-36	Rotating position	one	7024H
U0-37	Power factor perspective	0.1°	7025H
U0-38	ABZ position	one	7026H
U0-39	V/F separation target voltage	1V	7027H
U0-40	V/F separation output voltage	1V	7028H
U0-41	Direct display of DI input status	one	7029H
U0-42	Visual display of DO output status	one	702AH
U0-43	DI Function Status Visual Display 1 (Functions 01-40)	one	702BH
U0-44	DI Function Status Visual Display 2 (Functions 41-80)	one	702CH
U0-45	Fault information	one	702DH
U0-58	Z-signal counter	one	703AH
U0-59	Set frequency (%)	0.01%	703BH
U0-60	Operating frequency (%)	0.01%	703CH
U0-61	Inverter status	one	703DH
U0-62	Current fault code	one	703EH
U0-63	Point to point host communication sends torque values	0.01%	703FH
U0-64	Number of stations	one	7040H
U0-65	Torque upper limit	0.1%	7041H
U0-73	Motor serial number	0: Motor 1 1: Motor 2	7049H
U0-74	Inverter output torque	0.1%	704AH
U0-76	Low cumulative electricity consumption	0.1 degrees	704CH
U0-77	Accumulated high electricity consumption	1 degree	704DH
U0-78	linear velocity	1m/Min	704EH

Fault diagnosis and countermeasures

1. Safety precautions

danger

It is strictly prohibited to connect wires while the power is turned on. Please make sure to keep all circuit breakers in the OFF state. Otherwise, there is a risk of electric shock.

Warning

Please ensure that the frequency converter is grounded in accordance with local regulations. Otherwise, there may be a risk of electric shock or fire hazard.
Do not disassemble the casing or touch the internal circuit of the frequency converter when it is powered on. Otherwise, there is a risk of electric shock.
Fault inspection must be carried out by professionals, and non professionals are strictly prohibited from inspecting, maintaining, and repairing the frequency converter. Otherwise, there may be a risk of electric shock or fire hazard.
When installing the frequency converter in a closed cabinet or casing, please use a cooling fan or cooling air conditioner to fully cool it, so as to keep the intake temperature of the frequency converter below 50 ℃. Otherwise, it may cause overheating or fire.
Please tighten all screws according to the specified torque. Otherwise, there may be a risk of fire or electric shock.
Please confirm that the input voltage of the product is within the rated voltage range on the nameplate, otherwise there may be a risk of electric shock or fire.

Attention

When performing installation work, please cover the upper part of the inverter with a cloth or paper to prevent metal shavings, oil, water, etc. from entering the interior of the inverter during drilling. If foreign objects enter the interior of the frequency converter, it may cause the frequency converter to malfunction.
After finishing the homework, please remove these cloths or papers. If it continues to be covered, it will deteriorate the ventilation and cause abnormal heating of the frequency converter.
When operating the frequency converter, please follow the steps specified for electrostatic discharge (ESD) prevention measures, otherwise the internal circuits of the frequency converter may be damaged due to static electricity.

2. Adjustment guide before trial operation of frequency converter

1) Open loop vector control mode (P0-01=0 factory default value)

This control mode is used to control the speed and torque of the motor in applications where there is no encoder speed feedback. In this control mode, self-learning of motor parameters is required to achieve automatic tuning of motor parameters.

Problems and malfunctions	Countermeasures
Overload or overcurrent fault reported during motor start-up process	The motor parameters (P1-01~P1-05) are set according to the motor nameplate. Perform motor parameter tuning (P1-37), and if conditions permit, it is best to perform dynamic and complete motor tuning.
Slow torque or speed response below 5Hz, motor vibration	To improve the response of torque and speed, it is necessary to strengthen the proportional adjustment of the speed loop (P2-00 increases the set value by 10 units) or reduce the integration time of the speed loop (P2-01 decreases by 0.05 units); If there is vibration, it is necessary to weaken P2-00 and increase the parameter value of P2-01.
Slow torque or speed response above 5Hz, motor vibration.	To improve the response of torque and speed, it is necessary to strengthen the proportional adjustment of the speed loop (P2-03 increases the set value by 10 units) or reduce the integration time of the speed loop (P2-04 decreases by 0.05 units); If there is vibration, it is necessary to weaken P2-03 and increase the parameter value of P2-04.
Low speed accuracy	When the speed deviation of the motor under load is too large, the vector slip compensation gain (P2-06) needs to be increased or decreased by 10%.
Large speed fluctuations	When there is abnormal fluctuation in motor speed, the speed filtering time (P2-07) can be appropriately increased in units of 0.001s.
The motor has loud noise	Appropriately increase the carrier frequency value (P0-15), increasing in units of 1.0KHz; (Note: Increasing the carrier frequency of the motor will increase the leakage current)
Insufficient motor torque or output	Is the torque upper limit restricted? Increase the torque upper limit (P2-10) in speed mode; Increase torque command in torque mode

2) Closed loop vector control mode (P0-01=1)

This mode is used in applications where the motor has encoder speed feedback. It is necessary to correctly set the number of encoder lines, encoder type, and signal direction to achieve automatic tuning of motor parameters.

Problems and malfunctions	Countermeasures
Start reporting overcurrent or overload fault	Correctly set the number, type, and direction of encoder lines
Overload or overcurrent fault reported during motor rotation	The motor parameters (P1-01~P1-05) are set according to the motor nameplate. Perform motor parameter tuning (P1-37), and if possible, it is best to perform dynamic and complete motor tuning.
Slow torque or speed response below 5Hz, motor vibration	To improve the response of torque and speed, it is necessary to strengthen the proportional adjustment of the speed loop (P2-00 increases the set value by 10 units) or reduce the integration time of the speed loop (P2-01 decreases by 0.05 units); If there is vibration, it is necessary to reduce the values of the P2-00 and P2-01 parameters.
Slow torque or speed response above 5Hz, motor vibration.	To improve the response of torque and speed, it is necessary to strengthen the proportional adjustment of the speed loop (P2-03 increases the set value by 10 units) or reduce the integration time of the speed loop (P2-04 decreases by 0.05 units); If there is vibration, it is necessary to reduce the values of the P2-03 and P2-04 parameters.
Large speed fluctuations	When there is abnormal fluctuation in motor speed, the speed filtering time (P2-07) can be appropriately increased in units of 0.001s.
The motor has loud noise	Appropriately increase the carrier frequency value (P0-15), increasing in units of 1.0kHz; (Note: Increasing the carrier frequency of the motor will increase the leakage current)
Insufficient motor torque or output	Is the torque upper limit restricted? Increase the torque upper limit (P2-10) in speed mode; Increase torque command in torque mode

3) V/F control mode (P0-01=2)

This mode is used in applications where the motor does not have encoder speed feedback, and is not sensitive to motor parameters. Only the rated voltage and rated frequency values of the motor need to be set correctly.

Problems and malfunctions	Countermeasures
Motor oscillation during operation	Increase the oscillation suppression parameter (P3-11) in units of 10 (maximum adjusted to 100);
High power starting alarm overcurrent	Reduce torque boost (P3-01), adjust in units of 0.5%;
Excessive current during operation	Correctly set the rated voltage (P1-02) and rated frequency (P1-04) of the motor; Reduce torque boost (P3-01), adjust in units of 0.5%;
The motor has loud noise	Appropriately increase the carrier frequency value (P0-15), increasing in units of 1.0kHz; (Note: Increasing the carrier frequency of the motor will increase the leakage current)
Sudden unloading overload reports overvoltage, deceleration reports overvoltage	Confirm that the overvoltage stall enable (P3-23) is set to the enable state; Increase the overvoltage stall gain (P3-24/P3-25, factory 30) in units of 10 (maximum adjusted to 100); Reduce the overvoltage stall action voltage (P3-22 factory 770V) in units of 10V (minimum adjusted to 700V);
Sudden overload reporting overcurrent, acceleration reporting overcurrent	Increase the overcurrent stall gain (P3-20 factory 20) in units of 10 (maximum adjusted to 100); Reduce the overcurrent stall action current (P3-18 factory 150%) by 10% (minimum adjusted to 50%);

3. Fault alarm and countermeasures

During the use of the frequency converter, the following types of faults may be encountered. Please refer to the following methods for simple fault analysis:

Fault name and panel display	Troubleshooting of the cause of the malfunction	Fault handling measures
Accelerated overcurrent Err02	The output circuit of the frequency converter is grounded or short circuited	Eliminate peripheral faults and check if there is a short circuit in the motor or interruption contactor
	Control mode is FVC or SVC without parameter identification	Set motor parameters according to the motor nameplate and identify motor parameters
	Rapid acceleration condition, acceleration time set too short	Increase acceleration time
	Inappropriate setting for overcurrent stall suppression	Confirm that the overcurrent stall suppression function (P3-19) has been enabled; The set value of overcurrent stall action current (P3-18) is too high. It is recommended to adjust it within 120% to 150%; The overcurrent stall suppression gain (P3-20) is set too small, and it is recommended to adjust it within 20 to 40;
	Manual torque increase or inappropriate V/F curve	Adjust manual torque or V/F curve
	Start the rotating motor	Choose to start with speed tracking or wait for the motor to stop before starting again
	Affected by external interference	Check the historical fault records. If the current value during the fault is far from reaching the overcurrent point value, it is necessary to search for the interference source. If there are no other sources of interference, it may be a problem with the driver board or Hall devices.
Deceleration overcurrent Err03	The output circuit of the frequency converter is grounded or short circuited	Eliminate peripheral faults and check whether the motor has a short circuit or open circuit
	Control mode is FVC or SVC without parameter identification	Set motor parameters according to the motor nameplate and identify motor parameters
	Rapid deceleration condition, deceleration time set too short	Increase deceleration time
	Inappropriate setting for overcurrent stall suppression	Confirm that the overcurrent stall suppression function (P3-19) has been enabled; The set value of overcurrent stall action current (P3-18) is too high. It is recommended to adjust it within 120% to 150%; The overcurrent stall suppression gain (P3-20) is set too small, and it is recommended to adjust it within 20 to 40;
	No braking unit or braking resistor added	Add braking unit and resistor
	Affected by external interference	Check the historical fault records. If the current value during the fault is far from reaching the overcurrent point value, it is necessary to search for the interference source. If there are no other sources of interference, it may be a problem with the driver board or Hall devices.
Constant speed overcurrent Err04	The output circuit of the frequency converter is grounded or short circuited	Eliminate peripheral faults and check whether the motor has a short circuit or open circuit
	Control mode is FVC or SVC without parameter identification	Set motor parameters according to the motor nameplate and identify motor parameters
	Inappropriate setting for overcurrent stall suppression	Confirm that the overcurrent stall suppression function (P3-19) has been enabled; The set value of overcurrent stall action current (P3-18) is too high. It is recommended to adjust it within 120% to 150%; The overcurrent stall suppression gain (P3-20) is set too small, and it is recommended to adjust it within 20 to 40;
	The selection of frequency converter is too small	In a stable operating state, if the operating current exceeds the rated current of the motor or the rated output current of the frequency converter, please choose a frequency converter with a higher power level
	Affected by external interference	Check the historical fault records. If the current value during the fault is far from reaching the overcurrent point value, it is necessary to search for the interference source. If there are no other sources of interference, it may be a problem with the driver board or Hall devices.
Accelerated overvoltage Err05	Input voltage is too high	Adjust the voltage to the normal range
	During the acceleration process, there is an external force dragging the motor to run	Cancel additional power or install braking resistors
	Inappropriate overvoltage suppression setting	Confirm that the overvoltage suppression function (P3-23) has been enabled; The set value of the overvoltage suppression action voltage (P3-22) is too high. It is recommended to adjust it within 770V~700V; The overvoltage suppression gain (P3-24) is set too small. It is recommended to adjust it within 30 to 50;
	No brake unit or brake resistor installed	Install brake unit and resistor
	The acceleration time is too short	Increase acceleration time
Deceleration overvoltage Err06	Inappropriate overvoltage suppression setting	Confirm that the overvoltage suppression function (P3-23) has been enabled; The set value of the overvoltage suppression action voltage (P3-22) is too high. It is recommended to adjust it within 770V~700V; The overvoltage suppression gain (P3-24) is set too small. It is recommended to adjust it within 30 to 50;
	During the deceleration process, there is an external force dragging the motor to operate	Cancel additional power or install braking resistors
	The deceleration time is too short	Increase deceleration time
	No brake unit or brake resistor installed	Install brake unit and resistor
Constant speed overvoltage Err07	Inappropriate overvoltage suppression setting	Confirm that the overvoltage suppression function (P3-23) has been enabled; The set value of the overvoltage suppression action voltage (P3-22) is too high. It is recommended to adjust it within 770V~700V; The overvoltage suppression frequency gain (P3-24) is set too small. It is recommended to adjust it within 30 to 50; The maximum rise frequency for overvoltage suppression (P3-26) is set too low, and it is recommended to adjust it within 5-20Hz;
Constant speed overvoltage Err07	There is external force dragging the motor during operation	Cancel additional power or install braking resistors
Buffer power failure Err08	母线电压在欠压点上下波动	Seeking technical support
Undervoltage fault Err09	Instantaneous power outage	Enable the instantaneous stop function (P9-59) to prevent under voltage faults caused by instantaneous power outages
	The input voltage of the frequency converter is not within the range required by the specifications	Adjust the voltage to the normal range
	Abnormal bus voltage	Seeking technical support
	Abnormal rectifier bridge, buffer resistor, driver board, and control board	Seeking technical support
Inverter overload Err10	Is the load too large or is there motor stalling	Reduce the load and check the motor and mechanical condition
Inverter overload Err10	The selection of frequency converter is too small	Choose a frequency converter with a higher power level
Motor overload Err11	Is the setting of motor protection parameter P9-01 appropriate	Set this parameter correctly
Motor overload Err11	Is the load too large or is there motor stalling	Reduce the load and check the motor and mechanical condition
input phase loss Err12	The three-phase input power supply is abnormal	Check and eliminate problems in the peripheral circuits
input phase loss Err12	Abnormal driving board, lightning protection board, main control board, rectifier bridge	Seeking technical support
Output phase loss Err13	Motor failure	Check if the motor is open circuited
	The lead from the frequency converter to the motor is abnormal	Eliminate peripheral faults
	The three-phase output of the frequency converter is unbalanced during the operation of the motor	Check if the three-phase winding of the motor is normal and eliminate the fault
	Abnormal driver board and IGBT module	Seeking technical support
Module overheating Err14	The ambient temperature is too high	Reduce the ambient temperature
	Air duct blockage	Clean the air duct
	Fan damaged	Replace the fan
	Module thermistor damaged	Seeking manufacturer services
	Inverter module damaged	Seeking manufacturer services
External device malfunction Err15	Input external fault signals through the multifunctional terminal DI	Check the peripheral faults, confirm that the machine is allowed to restart (P8-18), and reset the operation
External device malfunction Err15	Input external fault signals through virtual IO function	Confirm that the parameters of the A1 virtual IO group are set correctly, reset and run
communication failure Err16	The upper computer is not working properly	Check the wiring of the upper computer
	The communication line is abnormal	Check the communication connection cable
	Communication expansion card P0-28 is not set correctly	Correctly set the type of communication expansion card
	Communication parameter PD group settings are incorrect	Set communication parameters correctly
	After completing the above tests, the fault still cannot be eliminated	You can try restoring the factory settings.
Contactor failure Err17	Abnormal driver board and power supply	Seeking manufacturer services
	Abnormal contactor	Seeking manufacturer services
	Abnormal lightning protection board	Seeking manufacturer services
Current detection fault Err18	Check for abnormal Hall devices	Seeking manufacturer services
Current detection fault Err18	Driver board abnormality	Seeking manufacturer services
Motor tuning fault Err19	The motor parameters are not set according to the nameplate	Set the motor parameters correctly according to the nameplate
	Parameter identification process timed out	Check the leads from the frequency converter to the motor
		Check if the number of encoder wires is set correctly P1-27, and if the signal wires of the encoder are connected correctly and securely
Encoder failure Err20	Encoder model mismatch	Set the encoder type correctly according to the actual situation
	Encoder wiring error	Detecting PG card power supply and phase sequence
	Encoder damaged	Replace the encoder
	PG card abnormality	Replace PG card
EEPROM Read/write malfunction Err21	EEPROM chip damaged	Seeking manufacturer services
Short circuit fault to ground Err23	Motor short circuit to ground	Replace cables or motors
Accumulated running time Arrival malfunction Err26	Accumulated running time reaches the set value	Use parameter initialization function to clear record information
user-defined Fault 1 Err27	Input user-defined fault 1 signal through the multifunctional terminal DI	Reset operation
user-defined Fault 1 Err27	Input user-defined fault 1 signal through virtual IO function	Reset operation
user-defined Fault 2 Err28	Input the signal of user-defined fault 2 through the multifunctional terminal DI	Reset operation
user-defined Fault 2 Err28	Input user-defined fault 2 signal through virtual IO function	Reset operation
Accumulated power on time Arrival malfunction Err29	Accumulated power on time reaches the set value	Use parameter initialization function to clear record information
Load shedding fault Err30	The operating current of the frequency converter is less than P9-64	Confirm whether the load is detached or whether the parameter settings of P9-64 and P9-65 are in line with the actual operating conditions
Run time PID Feedback loss fault Err31	PID feedback is less than the set value of PA-26	Check the PID feedback signal or set PA-26 to an appropriate value
PID low limit alarm Err32	PID feedback is less than the set value of PE-15	Set PE-15 as an appropriate value
PID high limit alarm Err33	PID feedback is greater than the set value of PE-13	Set PE-13 as an appropriate value
Water shortage alarm Err34	Operating frequency higher than PE-09 and output current lower than PE-11	Set PE-08 and PE-11 to an appropriate value
Water shortage alarm Err34	Operating frequency higher than PE-09 and feedback pressure lower than PE-08	Set PE-08 and PE-11 to an appropriate value
Wave by wave current limiting fault Err40	Is the load too large or is there motor stalling	Reduce the load and check the motor and mechanical condition
Wave by wave current limiting fault Err40	The selection of frequency converter is too small	Choose a frequency converter with a higher power level
Run time switching Motor failure Err41	Change the current motor selection through terminals during the operation of the frequency converter	Perform motor switching operation after shutting down the frequency converter
Speed deviation Excessive malfunction Err42	Incorrect encoder parameter settings	Correctly set encoder parameters
	No parameter identification has been carried out	Perform motor parameter identification
	The detection parameters P9-69 and P9-70 for excessive speed deviation are not set properly	Reasonably set detection parameters according to the actual situation
Motor overspeed fault Err43	Incorrect encoder parameter settings	Correctly set encoder parameters
	No parameter identification has been carried out	Perform motor parameter identification
	The setting of motor overspeed detection parameters P9-67 and P9-68 is unreasonable	Reasonably set detection parameters according to the actual situation
Motor overheating fault Err45	Loose wiring of temperature sensor	Check the wiring of the temperature sensor and troubleshoot any issues
Motor overheating fault Err45	Motor temperature is too high	Raise the carrier frequency or take other heat dissipation measures to dissipate heat from the motor
Master-slave control Slave malfunction Err55	The slave has malfunctioned, check the slave	Troubleshooting according to the slave fault code

4. Common faults and their solutions

serial number	Fault phenomenon	Possible reasons	treatment method
one	No display when powered on	The voltage of the power grid is either not high or too low	Check the input power supply
		Switching power supply fault on the frequency converter drive board	Check if the 24V and 10V output voltages on the control board are normal
		The connection between the control board, driver board, and keyboard is broken	Re plug and unplug 8-core and 34 core ribbon cables
		The buffer resistor of the frequency converter is damaged	Seeking manufacturer services
		Control board and keyboard malfunction
		Damaged rectifier bridge
two	Always displaying when powered on -A-C-	Poor contact of the wiring between the driver board and the control board	Re plug and unplug the 8-core and 28 core ribbon cables
		Related components on the control board are damaged	Seeking manufacturer services
		Motor or motor wire has a short circuit to ground
		Hall fault
		The voltage of the power grid is too low
three	Power on display report Police display Err23	Motor or output line short circuited to ground	Measure the insulation of the motor and output line with a shaking table
three	Power on display report Police display Err23	The frequency converter is damaged	Seeking manufacturer services
four	Power on frequency converter Display is normal, Display after running -A-C- And immediately shut down the machine	Fan damage or blockage	Replace the fan
five	Frequent reporting Err14 (mold) Block overheating) Obstacle Err14	The carrier frequency is set too high	Reduce carrier frequency (P0-15)
six	Inverter operation rear motor Do not rotate	Fan damage or air duct blockage	Replace the fan and clean the air duct
		Internal components of the frequency converter are damaged (thermistor or other)	Seeking manufacturer services
		Poor contact between the driver board and control board connection	Re plug and unplug the connecting wire, confirm that the wiring is secure;
		Driver board malfunction	Seeking manufacturer services
seven	DI terminal failure	Parameter setting error	Check and reset the relevant parameters of P4 group
		External signal error	Reconnect the external signal line
		OP and+24V jumper loose	Reconfirm the OP and+24V jumper wires and ensure they are securely fastened.
		Control board malfunction	Seeking manufacturer services
eight	Closed-loop vector control Timing, electricity Machine speed cannot be reached enhance	Encoder failure	Replace the code wheel and reconfirm the wiring
eight		Encoder wiring error or poor contact	Reconnect the wires to ensure good contact
nine	Frequent frequency converter Report overcurrent and overcurrent Pressure fault	Incorrect motor parameter settings	Reset motor parameters or perform motor tuning
		Inappropriate acceleration and deceleration time	Set appropriate acceleration and deceleration times
		Load fluctuation	Seeking manufacturer services
ten	power on (or run) Report Err17	Soft start contactor not engaged	Check if the contactor cable is loose Check if the contactor is faulty Check if there is a fault in the 24V power supply of the contactor Seeking manufacturer services

Products

4.5-5KW High performance vector frequency converter